Activeforever Invisia Collection Soap Dish with Integrated Suppo Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Santé et hygiène Activeforever Invisia Collection Soap Dish with Integrated Suppo. Activeforever Invisia Collection Soap Dish with Integrated Support Rail User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 4
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
-Wood studs.
-Adequate wood structural backing.
-No aligning structural wood studs.
-Suitably strong structural wall board.
#10 x 3" S/S
Screw and Lock
Washer
#10 x 3" S/S Bolt
with SnapToggle®
toggle bolts
STRUCTURE BEHIND WALL
(Wall Surface: Tile on 1/2" min cement board)
FASTENER
COMBINATION
www.ActiveForever.com
Invisia
Soap Dish
Installation Instructions:
SD-CRP / SD-PCW
THANK YOU...
Thank you for purchasing the Invisia Soap Dish. We are
confident that you will find the unique design and durable
construction of this product to be of great assistance in your
daily routine.
To fully enjoy your Invisia Soap Dish, please take a few
moments to read these instructions. You should store these
instructions in a safe place for future reference.
SAFETY CONSIDERATIONS
CAUTION: It is your responsibility to see that your Invisia
Soap D
ish is properly assembled, installed, and cared for.
Failure to follow instructions in this manual could result in
serious injury. Support rails can be slippery when wet - use
this product with caution.
INVISIA™ SOAP DISH INSTALLATION
The InvisiaSoap Dish should only be installed in areas where
the mounting surface is structurally sound. Strengthening
modifications may be required (see page 3 for details). Should
not be installed in fiberglass / acrylic shower enclosures
with
insufficient stiffness and strength. Should not be installed into
metal studs. If you are not equipped to undertake the outlined
work we recommend that you have your InvisiaSoap Dish
installed by a qualified contractor. Suggested maximum user
weight of support rail is 350lbs/159kg, however this rating is
conditional upon suitable fasteners and supporting surface.
Tray for soap is not a weight bearing surface.
WARRANTY
All HealthCraftProducts are cover
ed by a one year limited
warranty with the exception of hand grips which are subject to
normal wear. Buyer hereby indemnifies, agrees to hold
harmless and defend HealthCraft Products Inc. from and
against any and all liabilities, claims, (founded and
unfounded), losses, damages, costs and expenses (including
without limitation consequential damages and reasonable
professional fees) resulting from buyers specification,
application, or improper use of goods described hereo
n;
buyers omission or neglect.
HealthCraftProducts Inc. does not assume any liability for
damage resulting from services performed by others or faulty
installation, misuse or misapplication of goods sold by
HealthCraft™ Products Inc.
HealthCraft™ Products Inc. shall not be liable for prospective
profits or special, indirect, or consequential damages, or for
the cost of any corrective work done without HealthCraft
Products Inc. prior approval. HealthCraftProduc
ts Inc. total
liability hereunder shall in no event exceed the purchase price
of the goods specified hereon.
TOOLS REQUIRED
• Level Personal Protective Eyewear
Hammer Carbide tip drill suitable for tile
Stud Finder • Protective blanket
FASTENERS: INSTALLATION & MAINTENANCE
The Invisia Soap Dish must be secured to the wall with
fasteners appropriate to the structural material. Inspect, or
have inspected (and tighten if necessary) the screws on a
monthly basis. Included are 2 sets of mounting hardware for
different wall applications.
For tile walls judged to be suitably strong, for moderate
support weight bearing applications, you may choose to use
the supplied SnapToggle® toggle bolts without reinforcing
structural improvement. In
this case, locating the top wall stem
of the support rail with a wall stud is recommended.
If you are using fasteners other than the ones supplied, we do
not recommend flat head style screws (i.e. a screw that
requires a countersunk hole). We recommend stainless steel
fasteners / lock washers (to prevent rusting). Also, residue
from steel drill bits and other non-stainless steel tools may
cause rust stains. Properly clean metal chips, debris etc. prior
to exposing to water.
TIPS FOR DRILLING
INTO TILE
Use carbide tipped masonry drill on ceramic, or consider a
diamond tip drill for porcelain tile.
If possible, drill a smaller pilot hole first.
Be careful to prevent the drill from moving when you first
start it rotating - use duct tape or a wood guide on the
surface of the tile to hold the drill from walking sideways.
A variable speed drill on slow is best to start the hole. Do
not apply too much pressure when drilling. Do not use a
hammer drill.
WATERPROOFING
Although mounting hardware includes rubber gasket washer,
we recommend that sealant be applied around the wall
contact points for any products mounted in the shower. If not
properly sealed, there is the potential for water to seep into the
wall. This may cause the wood to rot, thus compromising the
structure the support rail is attached to.
CORIAN: CLEANING AND MAINTENANCE
The InvisiaCollection features several tray surfaces made
from Duponts Corian® material. It is a very
durable,
non-porous material that resists the growth of bacteria. Clean
with general household cleaners. The surfaces & edges can
be sanded and buffed to repair if necessary.
Page 1 of 4
Vue de la page 0
1 2 3 4

Résumé du contenu

Page 1 - Soap Dish

-Wood studs.-Adequate wood structural backing.-No aligning structural wood studs.-Suitably strong structural wall board.#10 x 3" S/S Screw and Lo

Page 2 - 4-6"

LevelFigure 1.Figure 5.Figure 3a. Figure 3a.LockWasherMOUNTING LOCATIONWe strongly recommend that you give some thought as to the optimal location o

Page 3

LHBABATHROOMTILE WALLBACKSIDEACCESS TOBATHROOMTIPS FOR LOCATING A WOOD STUD• For drywall surfaces, use a stud sensor to locate a stud. • For tile surf

Page 4 - Page 4 of 4

SD302 (x3)Assembly, Inner Stem with PSA and Oring, SDHW222 (x3)Set Screw, Hex Socket, 10-32 x .25" L, S/SSD200 (CRP/PCW)Weldment, Handle, SDSD301

Commentaires sur ces manuels

Pas de commentaire