OPERATION INSTRUCTIONS FOR THE AIRFLOW
BREEZE ULTRA WITH REMOTE CONTROL
MODEL SERIES 7.1
READ AND SAVE THESE INSTRUCTIONS AND
IMPORTANT NOTICE
INSTALLATION:
Floor registers 6”x10” or 6”x12”
1. Remove the round cap on the grill top.
2. Route the plug end of the AC adapter through the round
opening and plug into the underside of the Ultra.
3. Place round cap with slot on the grill top.
4. Plug the AC adapter into the 120V AC wall outlet .
5. Follow the Operation Settings.
6. Remove the oor register and replace with the U ltra.
Wall or Ceiling registers 6”x10” or 6”x12”
1. Drill (2) holes with a 3/16” drill bit from the bottom side of the
Breeze. The holes should be drilled in the pre-mol ded
locations as pictured below.
2. Remove the round cap on the grill top
3. Route the plug end of the AC adapter through the round
opening and plug into the underside of the Ultra.
4. Place round cap with slot on the grill top.
5. Plug the AC adapter into the 120V AC wall
outlet .
6. Follow the Operation Settings.
7. Remove the wall or ceiling register and replace with the
Ultra.
Note: If you choose to hard wire the Ultra, install the n ecessary 120V
AC outlet near the backside of the Ultra then plug into the rear of the
unit. Use the non-slotted grill cap to trim out th e Ultra top.
Power Receptacle Po wer Cord Access Hole
Wall and Ceiling Drill Hole Locations
6” X 10” 6”
x 12”
Operation Settings
:
Mode Selections:
• FAN (green) for continuous running
• HEAT (red) for automatic ON/OFF to boost warm air
• COOL (blue) for automatic ON/OFF to boost cool air
Display shows SET POINT
temperature setting for
HEAT and COOL
FAN Speed Settings
REMOTE CONTROL INSTRUCTIONS
• Press ON/OFF button to turn Breeze Ultra on.
• Press MODE button for FAN (green) and select fan s peed
(Suggest HIGH to s
tart.)
• For heating
press the MODE button and select HEAT (red).
Adjust SET POINT down until fans ar e on, then
adjust SET POINT up until fans turn o. Unit is now set.
• For cooling
press MODE button and select COOL (blue).
Adjust SET POINT up until fans are on, and then adj ust
SET POINT down until fans turn o. Unit is now se t.
• Return to INSTALLATION directions #6 or #7.
UP
DOWN
IMPORTANT NOTES
1. Fan speed light will ash when fans are running .
2. Fan speed can be set at any time. Fans do not h ave to be
running.
3. Numeric display will go out 30 seconds after SET POINT is
completed.
4. The numeric display will
only be active in the H eat or Cool mode.
5. The numeric display will come on in Heat or Cool if any button is
pressed.
6. The numeric display exhibits an approximate room temperature
for the purpose of programming the electronic senso r.
7. To shorten the length of time your Breeze Ultra runs after your
forced air furnace or air conditioner has shut o
a. for HEAT raise the SET POINT temperature
b. for COOL lower the SET POINT temperature
8. If power f
ails or the Breeze Ultra is turned o the Ultra will
automatically retain all settings.
Medical Supplies, Safety Equipment & Innovative Health Products
ActiveForever
10799 N. 90th St.
Scottsdale, AZ 85260
www.ActiveForever.com
(480)767-6800
(800) 377-8033
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels